Best Oscillating Tool Blades of 2026

A 64-piece box sounds like overkill until you are halfway through a trim job and the blade that fits the cut has gone dull. The PECHAM set is built around that moment: a broad mix of standard cutting blades, a titanium coating on the teeth, and enough repeats that you can swap rather than stop. The quick-release mount is the other practical part, since it lets you move between shapes without hunting for a wrench.

What we like best is the balance of the mix. The wood and plastic blades cover the everyday cuts, and the titanium-coated teeth give you a little more margin in light metal and nail-embedded trim than a plain high-carbon blade. The length markings on both sides are a small detail we appreciate: they make a plunge cut easier to line up when the blade is buried in a cabinet side or a piece of trim.

The catch is the metal side. This is not the kit to buy for repeated cuts through hardened bolts or a nail-heavy demolition job; the blades are at their best in wood, drywall, and plastic, with light metal as the occasional task. The universal mount also needs a check against your tool. Standard OIS chucks are the easy fit, while some quick-release and older clamp designs need an adapter or a different blade.

For a mixed renovation list, this is the set we keep within reach: broad enough to cover the common cuts, small enough to store, and not a specialty purchase. If your work is mostly thick stock or nails, the long LEILUO set is the better reach; if you want a compact case, the DEWALT kit is the neater choice.

The DEWALT kit is the one we take when the job is small and the tool bag is already full: five blades, a compact Tough Case, and no loose extras to sort through. That focus is the appeal. Instead of a hundred pieces you may never use, you get a few shapes that cover plunge cuts, flush cuts, and the occasional nail.

The bi-metal blades are the reason to pay for this set over a budget high-carbon box. The cutting edge is designed to survive a nail strike in reclaimed trim, and the PlungePoint tip lets you start a cut on a marked line without drilling a starter hole. Tool-free changes on the universal mount are another convenience we value when you are switching between a wood blade and a metal blade on the same repair.

The set is built for finish work and nail-embedded trim, not for long drywall runs; for that, a high-carbon bulk set goes further. The value case is the blade that keeps cutting when it hits a hidden fastener, where one good blade is worth more than a stack of cheap ones.

We also like the case more than most. It is small enough to live in a drawer, and the molded slots keep the blades from rattling together. The one check is the mount: the universal fitment covers many tools, but Starlock and some quick-change chucks are not the same thing.

Fifty-five blades is a lot of blade changes before you need to restock. The Bionso kit gives you a deep bench of standard blades, a handful of shapes for trim and drywall, and enough spares that a dull edge is a swap rather than a trip to the store.

We like the variety for general DIY. The standard tooth blades handle pine, plywood, and drywall, and the finer shapes are useful for trim and plastic. The universal interface covers a lot of tools, including DeWalt and Ryobi, but it is not a guarantee; Bosch OIS and some quick-release models are the common exceptions, so check the arbor before you order.

The metal side is where the kit narrows. Only two of the 55 pieces are meant for metal, and they are for nails and light stock rather than thick steel. That is not a flaw if you buy it for wood; it is a flaw if you expect one box to do a demolition job. We think it is a strong woodworking value, not a metalworking kit.

The blades also lose their bite faster than premium bi-metal in abrasive material, which is the trade-off for the count. In a wood-heavy remodel, the math works: you reach for a fresh blade and keep moving. In a metal-heavy shop, spend the money on a smaller bi-metal set.

Most blade kits stop at cutting. This one keeps going into surface prep with sandpaper pads and scraping accessories, which is why it earns a place in a renovation kit rather than just a cutting box.

The breadth is the draw. You get ten blade types plus sandpaper, so you can cut trim, scrape adhesive, and smooth a patch without changing kits. The stainless steel blades are the ones we reach for on light metal and general scraping, while the high-carbon blades handle wood and plastic. For a job that moves between cutting and cleanup, that saves time.

The durability is the part we weigh most. These are not production-grade blades for daily metal cutting, and the edge can fade on hard material. For occasional DIY and finish work, the variety outweighs that; for a metal-heavy shop, a smaller bi-metal set is the better buy.

We like it best as the one box that covers cutting, sanding, and scraping in a standard OIS tool. The case is big enough to keep the pads and blades together, which is useful until you have to find drawer space for it.

Deep reach is the reason this set exists: two 55mm blades and two 70mm blades let you plunge past the shoe and into thick stock without flipping the tool or cutting from both sides. For a homeowner trimming a door jamb or notching a beam, that extra length is the difference between a clean cut and a workaround.

The mix is smart for the size. You get the long Japanese-tooth blades for fast wood cuts, a titanium bi-metal blade for wood with hidden nails, and two standard 44mm blades for everyday surface work. The three adapters broaden the fit, and the red teeth are easy to spot in a crowded case. We like that the set gives you one nail-capable blade without making every blade expensive.

The catch is that long blades are not the answer to every cut. They can flex in a tight curve, and the set is small enough that one broken blade matters. Compatibility is the bigger check: the universal interface covers many tools, but Makita and Dremel quick-change users need to confirm the arbor before buying, and a blade that does not seat fully is not safe to use.

For deep cuts in lumber, thick trim, or pipe, this is the set we reach for before a standard kit. It is a specialist, not the box you buy for a whole renovation.

If your oscillating tool is old enough that the manual lists a dozen brand names, this is the kit to check first. HYSHIER's compatibility list runs from Fein Multimaster and Bosch Multi-X to Craftsman Nextec, Dremel MM40 and MM45, and a long tail of older clamps, which is unusual in a budget set.

We like the 50-piece count for a simple reason: it lets you keep a spare in the case and another in the tool bag without treating blades like precious goods. The high-speed and high-carbon steel construction is aimed at wood, plastic, drywall, and soft metal, and the length markings on both sides are useful for repeat cuts.

The edge is the trade-off. These are not premium blades, and the teeth lose bite on abrasive material such as drywall and old flooring. For a homeowner cutting trim or clearing a small opening, that is acceptable; for daily production work, a bi-metal set lasts longer.

The fit list is also not a guarantee. A blade that does not seat flat is not worth forcing, and the clamp has to pull it tight against the flange. If your tool has a simple clamp and you want a deep bench of cheap blades, this is a practical choice.

A 26-piece kit is a sensible first purchase if you already own an oscillating tool and have been making do with the one blade in the box. It is small enough to store, varied enough to cover the common jobs, and inexpensive enough that you can experiment with tooth shapes before buying a bigger set.

The mix covers wood, plastic, and light metal, and the finer-toothed blades are the ones we reach for on trim and plastic. The fit is a strong point for a budget kit: it works with DeWalt and Ryobi One tools, and the adapters broaden it to other standard mounts. The compact case is easy to keep with the tool rather than in a drawer.

The trade-off is durability. These are homeowner blades, and the tips and welds are the first to fail if you lean on the tool or cut abrasive material all day. For occasional repairs, that is a fair exchange; for a remodeling crew, it is false economy.

The case is the part that makes it easy to live with: it keeps the blades with the tool instead of in a drawer, and the smaller count means you can actually see what you have. We recommend it as a first refill, not as the last kit you buy.

One hundred identical 1-3/8-inch blades is a strange-looking kit until you are cutting the same trim or drywall line over and over. Then the logic is clear: you want a fresh standard blade within reach, not a box of shapes you have to sort through.

The set is built for repetition. The high-carbon blades have length markings on both sides, the quick-release mount covers many standard tools, and the 100-count means you can keep a spare in the case and another in the tool bag. The blades are all the same 1-3/8-inch standard tooth shape, which is the point: fewer decisions, faster swaps.

That focus is the appeal. We like it for a drywall or woodworking run where you want to reach for a fresh blade without thinking about which tooth pattern to use. The single-size approach keeps the case simple and the cost per cut low, which is what a production carpenter or a homeowner with a repetitive project actually needs.

The trade-off is versatility: you are buying a deep bench of one blade, not a mixed kit. For the right repetitive job, though, the consistency is worth it.