Best Jigsaw Blades of 2026

The case is what keeps this set in our tool bag instead of in a drawer of loose blades. Fourteen blades sit in their own slots, so you can see at a glance which shapes are running low and pull the one you want without tipping the box out. It's small enough to drop into the jigsaw's own bag, which is where ours ended up.

What's inside is aimed at wood and metal, with both high carbon steel and bi-metal blades in the mix: the bi-metal ones take the cuts that punish a tooth, and the high carbon blades handle ordinary woodwork. There are duplicates of the common profiles, and that matters more than the headline count. A set that gives you a second blade of the shape you use most keeps you working when the first one snaps.

The balance is what earns it the top spot. It carries more blades than the Bosch set, the case is a genuine one rather than a sleeve, and it comes in well under the Diablo set while leaving you enough spares to actually use the saw. Nothing here is specialised, and that's the point — this is the box you keep by the saw and dip into for everything.

Fit is the standard T-shank, which DeWalt lists for its own saws and Bosch's, and T-shank is the fitting most current jigsaws take. That covers a lot of what's in a typical garage. If yours is an older saw with a U-shank clamp, check before ordering, because no amount of blade variety helps if the tang won't seat.

Ten blades, two each of five types, with three wood profiles and a basic metal blade among them: the Bosch T5002 is the value play here. The named blades are a 4-inch 10 TPI clean-for-wood, a shorter 3-1/4 inch blade for tighter curve work, a 6 TPI speed blade, and a basic metal blade. For most household cutting that's the whole vocabulary in one box.

The blades themselves carry the set. The bodies are stiff, which is what lets a curve come out smooth rather than wandering, and they're sharp enough out of the case to cut without a break-in period. Bosch also names the saws the set fits — over 90 percent of current jigsaws, with DeWalt, Makita, Milwaukee, Porter-Cable, and Craftsman among the brands listed — so the compatibility question is mostly answered before you buy.

As a first set or a top-up for the blades you actually wear out, this is the one we point budget-minded buyers to. It won't hold an edge like the Diablo blades in hardwood, and it doesn't give you the DeWalt set's number of spares, but it puts five blade types in your hands for very little money. That's a trade most occasional users should take.

Diablo shapes the blade body for the job rather than simply toothing it. The bodies are profiled for fast, clean cutting in wood at one end and extended life in metal at the other, and the difference lands where you notice it — a cut that needs less cleanup and a blade that keeps its line through thicker stock instead of bowing off it.

The set covers wood, metal, and plastic across twenty blades, and the T-shank fit is stated for every combo jigsaw plus most U-shank saws. That second half is worth knowing if your saw is older than the blades you're buying; plenty of sets only promise the modern clamp.

Cut quality is where these earn their keep. Edges come out clean, tear-out stays small as long as you match the blade to the material, and the teeth hold their sharpness through a run of cuts rather than fading halfway down a shelf. On trim, laminate, and anything where the offcut gets seen, that's the difference between reaching for sandpaper and being finished.

The frustration is that the listing doesn't itemize which twenty blades you get. If you buy by part number — a scrolling blade for a tight radius, a coarse one for fast ripping — you're guessing. Buy it as a box of good blades to work through, and it's the set we reach for when the cut has to look good.

Seven different part numbers in one case is what separates this set from the rest: five each of the T118A, T144D, and T101B, three each of the T123X and T101AO, and two each of the T127D and T345XF. That's a working selection rather than a sampler, and it's the set we suggest for anyone tired of buying blades one at a time.

The steel follows the job. High carbon blades handle general woodwork, high speed steel takes hardwoods, metal, and reinforced plastic, and the bi-metal blades are built for heavy cuts in hardwood and metal. In practice that means one case can follow a project from a rough cut through to finish trim without a run to the store in the middle of it.

The thin metal blades are the ones that give out first. The T118A profile in particular doesn't enjoy being pushed through heavy steel, which is the reason to slow the saw and let the teeth work when you're cutting metal rather than leaning on it. If metal is most of what you cut, the Diablo set is the better spend; if you cut mostly wood with the occasional bracket or channel, this box covers it.

Two of the thirteen blades cut on the downstroke, and that's the detail that earns this set a place. Most jigsaw blades cut on the upstroke and blow out the top face — the one you can see — so a shelf or a countertop edge comes out splintered right where it shows. A downcut blade pushes that tear-out onto the underside instead, and the visible edge comes away clean.

The rest of the box spans 6 to 24 TPI: 6 TPI for fast straight cuts, 10 and 12 for general work, 14 for cleaner edges, and 24 for thin stock and laminate where chipping is the enemy. If you want one box that covers everything from a rough cut to a finished plywood edge, that range is the reason to pick it.

Craftsman also publishes the cut capacities, which tells you more than a piece count does: fast cuts from 1/4 inch to 1-7/8 inch, downcuts from 3/16 inch to 1-1/4 inch, and metal up to 3/32 inch. That describes a woodworking set that will handle light sheet metal — a thin bracket, a hinge plate — rather than anything structural.

For finish carpentry and cabinet work in softwood and plywood, the downcut pair is the reason to choose this over a bigger assortment. It's a woodworking set first, and it's priced like a starter box rather than a premium one, which makes it an easy thing to keep alongside a larger set for the days that need a clean face.

Fifty blades for about what our top pick costs is the entire argument, and for the right buyer it's a good one. If you're cutting vinyl plank flooring, siding, or a long run of shelving and you expect to sacrifice a blade or two along the way, a full case changes how you work: you swap a blade that's dragging instead of pushing it through the rest of the job.

Six blade types cover wood, plastic, and metal work — T118A and T118B, T101AO, T101B, T101BR, and T144D — and they arrive in a storage case with the positions marked, which is more than a bag of loose blades gives you. The blades are labeled for quick identification, so pulling the right one mid-project doesn't mean squinting at tooth counts.

The six profiles are all basic shapes, so there's nothing here for the fine, splinter-free cuts a downcut blade gives you, and it's not the set to buy if you expect each blade to last. Judged as a box of blades to burn through on rough and mid-grade work, though, it's the best value per blade in this group, and that's the job it's selling for.

Twenty identical blades sounds like a mistake until you've spent an afternoon cutting curves. The T101AO is a 3-inch, 20 TPI scrolling blade with a narrow body, made for tight radii and clean edges in plywood, MDF, laminate, and hardwood veneer — the kind of cut where you creep along and let the teeth do the steering. Twenty of them means you stop rationing: when one starts dragging through a curve, it goes in the bin.

For window valances, speaker cutouts, or template work in veneered plywood, this little box is the cheapest way to keep a fresh blade in the saw. The pointed teeth are the catch — they don't take a plunge cut, and forcing one in chips the tip. Drill a starter hole and work out from there instead, and a single blade gets through a surprising amount of scroll work.

The Ryobi kit is the least ambitious set here, and that isn't a criticism — it's the one to hand someone who has just unboxed a first jigsaw. Ten bi-metal blades in all-purpose profiles, marked clearly enough that you can tell them apart without squinting, and a carry case that keeps them together in a bag rather than rolling around a drawer.

Fit is what decides this one. Ryobi lists the kit for its own saws, so if there's a Ryobi jigsaw on your bench you're buying blades the maker intends for that tool rather than guessing at compatibility from a spec line. As a first set it's an easy call, and the labeling is a real help when you're still learning which blade does what.

Bi-metal construction is the practical advantage over the high carbon sets here: it's the reason the kit walks through aluminum and light metal instead of folding, and it holds an edge longer in anything abrasive. The case turns out to matter more than it sounds, because a set that lives in the saw's bag is a set you actually use.